allparts.jpg
frame parts.jpg

 

Aluminum Booms

booms4small.jpg

If you are going to cut your own boom stock you can purchase the C-Channel here:

These are 9-5/8" long and cut from 1/2" x 96" C Channel 1/16" thick - Home Depot #56860

The layout for the boom holes can be found here: Kronos Flyer Platoform and Booms PDF

Don't want to make your own booms. We have them pre-cut and drilled. They are ready for assembly.

Kronos Flyer Boom Set

 

Platforms

platforms.jpg

If you are going to cut your own platform components you will need the following:

1 Sheet of 1/8" 12" x 30" Baltic Birch

or

6 Sheets of 1/8" 12" x 12" Birch Plywood

 

If you dont want to cut and drill your own platform components you can purchase a laser cut baltic birch platform set here: Kronos Flyer Platform Parts

 

Hardware

• 4, #6-32 x 2” Machine screws
• 4, #6-32 x 1-1/2” Machine screws
• 4, #6-32 x 5/8” Machine screws
• 12, #6-32 x 1” Machine screws
• 50, #6 Washers
• 36, #6 Hex nuts
• 4, #6 spacers 1/2" Long
• 16, #4-40 x 1/2" Machine Screws
• 16, #4-40 Locknuts
• 8, 8" tie wraps (cable ties)
• 16, 3" tie wraps (cable ties)
Vecro wraps or Lipo Battery Straps

 

Landing Gear

landinggear.jpg

Skid Set: HK# 500-139, Align # H50122

The parts below are optional. I prefer using other 1/4" round stock for my skid pipes. The aluminum pipes while they look good, tend to bend on hard landings. I cut my skid pips from driveway reflectors. Just make sure you get some that have 1/4" stakes. The stakes are made from fiberglass. It's a little heavy but can take a pounding.


Skid Nut Set: HK# GT500-141, Align # H50052
Pipe Set: HK# GT500-140, Align # H50090

Order from Hobby King international warehouse

 

Motors

The following motors have been tested on the Kronos Flyer.

SK3 Motor

SK3 Motor

4, Turnigy Aerodrive SK3 – 2826 1130Kv motors

or


4, Turnigy Aerodrive SK3 – 2826 1240Kv motors

Order from Hobby King US or international warehouse

NTM Motor

NTM Motor

4, NTM Prop Drive 28-26A 1200Kv motors

4, NTM Prop Drive 28 series Accessory Pack

Order from Hobby King international warehouse

The NTM motor do not come with motor mounts or prop adapters, so you need to order a Accessory pack for each NTM motor. Also when ordering motors it is best to order an extra.

Tiger Motor

Tiger Motor

4, Tiger MT-2208-18 1100Kv motors

The Tiger motors come with extended length leads and when paired with the Multistart ESC require no soldering. While these motors are the most expensive they are the smoothest, quietest and most relaiable motors of the ones shown here.

ESC's

Turnigy Plush Series

Turnigy Plush Series

Turnigy Plush Series

4, Turnigy Plush 18 Amp HK# TR_P18A ESC's

or
4, Turnigy Plush 25 Amp HK# TR_P25A ESC's

or
4, Turnigy Plush 30 Amp HK# TR_P30A ESC's

 

You will need this programmer for the plush ESCs

plush programmer.jpg

Turnigy Plush BESC Programming Card

The Plush ESCs do not come with connectors on the leads. You will have to solder connectors to the leads. You will need these connectors when using the Plush ESCs

3.5mm Gold Connectors

 

Order from Hobby King international warehouse

 

UPdate:

The Turnigy Plush 18Amp ESC is now available at the HobbyKing USA warehouse.

4, Turnigh Plush 18 amp HK# TR_P18A

While you must still purchase the programming card from the international warehous this could be a good source for the ESC if they are out of stock elsewhere.

 

Turnigy Multistar Series

4, Turnigy Multistart 20 Amp HK# 9351000003

or

4, Turnigy Multistart 30 Amp HK# 9351000004

Note that the Turnigy Multistart ESCs have connectors pre-installed so you wont have to do any soldering.

 

You will need theis programmer for the Multistart ESCs

multistar programmer.jpg

Turnigy Multistar BESC Programming Card

Order from Hobby King international warehouse

 

IMPORTANT!!!!

When ordering your ESCs be sure to get a programing card as well. You will need the card that matches your ESC type. (Plush or Multistar)

 

Servo Tester

To calibrate the ESCs you will need a servo tester. The one shown below works great.

Servo Tester.jpg

Turnigy Servo Tester

Order from Hobby King international warehouse

Props

8045 green set: HK# 017000054

or
8045 blue set: HK# 017000053

or
8045 Orange set: HK# 017000056

or
8045 Yellow set: HK# 017000057

or
8045 Black set: HK# 017000058

or
8045 Red set: HK# 017000055

or

8045 Green Left Hand Props

8045 Green Right Hand Props

or

8045 Black Left Hand Props

8045 Black Right Hand Props

or

8040 x 3 GWS 3 Blade Counter Rotate Props

8040 x 3 GWS 3 Blade Props

 

Note that some of the props come as complete left and right rotation sets. These are shown with a single link. Others come in left or right hand rotaion. These are shown with two links.

Order from Hobby King international warehouse

 

Power Distribution Board

distribution board.jpg

Hobby King Quadcopter Power Distribution Board

Order from Hobby King US or international warehouse

Battery Monitor

On-Board Lipoly Low Voltage Alarm

Order from Hobby King international warehouse

Battery

battery.jpg

3, Turnigy nano-tech 2200mah 3S Lipo Pack

or

3, Turnigy 2200mah 3S Lipo Pack

 

Order from Hobby King US warehouse


Battery Charger

Turnigy Accucel-6 6A Charger: HK# ACC6

or

Turnigy Accucel-8 7A Charger

 

Order from Hobby King US warehouse

 

Power Supply

Hobbyking 105W 15V/7A Switching DC Power Supply

 

Order from Hobby King international warehouse

 

 

NAZA Flight Controller

naza.jpg